What Should a Startup Ask About Cleanroom Services Before Signing?
What Should a Startup Ask About Cleanroom Services Before Signing?
Ravi is a founder with a sensor idea, a small team and a very real fear of wasting money. Last month a vendor sent him a long quote with the words “cleanroom access” buried on page six. He couldn’t tell what it covered, and nobody on the call would say. He wanted a plain checklist, so let’s build one using InchFab’s own pages.
The goal isn’t to push you toward any provider. It’s to help you ask better questions when comparing cleanroom services and fab options. InchFab is a handy example because its pages are fairly specific, but the habits work anywhere you buy chip making help.
What Do Founders Usually Forget to Ask?
They forget to ask what’s actually included. A quote might say access, process time or support, and each word can mean something different. Ask for a list: which tools, how many runs, what measurements, and who handles problems when a lot comes out wrong.
They also forget to ask about change. Early designs move constantly. If every tweak means a new contract, your schedule will slip. InchFab says its platform is modular and easy to adapt as needs change, which is the kind of promise you should test with a real example.
How Do You Test a Speed Claim?
Ask for a worked case. If the pages say early development turnaround can be as fast as one week, ask what that covers: a simple flow, a typical sensor or a custom device? Then ask what slows it down. Honest answers usually mention things like extra steps or custom films.
Don’t be shy about this. A provider who explains delays clearly is easier to trust than one who only repeats the headline number. Ravi got a straight answer in two emails, and that told him more than a glossy slide ever could.
Should You Use Foundry Service or Your Own Line?
Start with volume and time. If you need a handful of lots over several wafer processing services months, sending designs to a foundry service is simpler. InchFab says its foundry work uses the same platform as its modular lines, so what you learn early can carry into larger runs later.
Owning a line starts to make sense when you run many wafers or need dedicated equipment. It also brings facility work: power, exhaust, water and space. The InchFab Line page lists those numbers, and they’re serious. A startup with a rented office probably isn’t ready for that jump yet.
What Does the Platform Say About Growth?
The homepage describes InchFab as modular, proprietary and scalable. The idea is to start small and expand as research, development or production needs grow. For a startup, that’s the important part, since you never know how fast your first customer will say yes.
The Foundry Service page adds that volume production comes with cost per chip that holds up against traditional 200mm to 300mm foundries. Again, it’s a claim from the company. Ask for numbers that match your volume, because a startup’s version of volume is usually smaller than anyone’s marketing example.
What Belongs in Writing?
Four things at least: your wafer size, your process flow, your target dates and the exact deliverables. InchFab’s line works on 100mm wafers, so if your design assumes another size, say it early. List the unit processes too, like lithography, DRIE, metal deposition or plating.
Also write down who owns what. Ask about intellectual property in your quote conversation, since the pages I read don’t state a policy. That’s a fair gap to raise, not a criticism. Founders who ask early rarely regret it, and founders who skip it sometimes do.
How Do You Ask for a Process Quote?
Use the Get a Process Quote button on the Foundry Service page, which leads to the contact page. You can also write to . Include your device type, layer stack, wafer count, target date and anything unusual. The clearer your note, the more useful the reply.
Ravi’s first note was three lines long and got a vague answer. His second was a full page with a layer list and a sketch, and the reply came back with real questions. Moral: detail invites detail. A short, vague request invites a short, vague quote.
What Are the Red Flags?
Watch for answers that dodge. If a provider can’t say what’s included, how long a run takes or how changes are handled, slow down. Also watch for pressure to sign before you’ve seen specifics. Good partners can handle questions without feeling threatened by them.
Another one: nobody asks about your device. A real team wants to know your layers, your tolerance for change and what keeps you up at night. If the conversation never gets there, you’re buying a generic slot, and your odd little chip deserves more than that.
So, What Should Ravi Do Next?
Send a detailed brief, ask for a worked example, compare the speed and cost claims against his own numbers, and keep the answers in writing. If the facility side looks heavy, lean on the foundry route. If it looks manageable, ask about a line.
A good decision about cleanroom services comes from clear questions, not clever sales talk. Ravi’s checklist now fits on one page. Yours can too. Print it, take it into your next call, and keep notes. You’ll be surprised how much calmer the whole thing feels.
FAQs
What should a startup ask first?
Ask what’s included, what turnaround is realistic for your device and how design changes are handled.
Does InchFab publish a quote button?
Yes. The Foundry Service page has a Get a Process Quote button leading to the contact page.
Which wafer size does the line use?
The InchFab Line page lists 100mm wafers.
Is the platform built to grow?
The homepage describes it as modular and scalable, so you can start small and expand over time.
Does the page state an IP policy?
No, the pages I read don’t mention one. Ask the team directly.
What's Your Reaction?
Like
0
Dislike
0
Love
0
Funny
0
Angry
0
Sad
0
Wow
0